Dishwasher Not Draining? 7 Causes and Fixes

Last updated: August 12, 2026

Quick answer: Start with the removable filter, then check the drain hose under the sink for a kink and confirm that the sink connection is clear. Do not use chemical drain opener in a dishwasher. If water remains, the pump hums without draining, or the breaker trips, stop and book dishwasher repair in Halifax.

Table of Contents

Clogged Drain Filter
Sink or Food-Waste Disposer Connection
Kinked or Clogged Drain Hose
Failing Drain Pump
Air Gap or High Loop
Stuck Check Valve
Control Board Fault
Error Codes by Brand
How to Prevent Drainage Problems
Frequently Asked Questions

Standing water can come from a blocked filter, a kinked or incorrectly routed hose, a blocked sink connection, a check valve, a pump fault or an electronic fault. Begin with the visible checks below and use the instructions for your exact model.

Manufacturer or safety reference: Whirlpool’s official dishwasher drainage guide covers the filter, sump, drain hose, sink or disposer connection and pump, and warns against drain-opening chemicals. Installation details remain model-specific.

1. The Drain Filter Is Clogged

A clogged filter is a common cause of dishwasher drainage problems and is one of the first safe checks. Every dishwasher has a filter at the bottom of the tub designed to catch food particles before they reach the drain pump. Over time, grease, food debris, and even small pieces of broken glass can clog it completely.

Filter care: Inspect and clean the removable filter at the interval stated in the model manual and whenever visible debris collects. Reinstall it fully before running a test cycle.

To clean it: remove the bottom dish rack, locate the cylindrical filter at the bottom centre of the tub, twist counterclockwise and pull it out, rinse under hot running water and scrub with a soft brush, then reinstall and run a short cycle to test.

2. The Sink or Food-Waste Disposer Connection Is Blocked

Some dishwashers drain into a sink tailpiece; others connect through a food-waste disposer where one is installed. A blocked sink connection can stop drainage. After a new disposer installation, the dishwasher inlet knockout may also need to be removed according to the disposer instructions.

Run the garbage disposal with water flowing for 15 to 20 seconds to clear any blockage. If you recently had a new disposal installed, check that the knockout plug on the dishwasher inlet was removed – this is a surprisingly common installation mistake.

3. The Drain Hose Is Kinked or Clogged

The drain hose connects your dishwasher to the drain under the sink. It can become kinked if the dishwasher was recently moved or pushed back into place, or clogged with accumulated grease and debris. Pull the dishwasher forward slightly and inspect the hose for kinks. If you suspect an internal clog, disconnect the hose (place a towel underneath to catch water) and flush it with hot water. If water does not flow freely through, the hose needs cleaning or replacement.

4. The Drain Pump Is Failing

Did you know? The drain pump on most dishwashers is not a wear item you would replace regularly – they typically last the life of the appliance. When they do fail, it is usually due to a foreign object (glass shard, piece of bone) getting past the filter and jamming the impeller. If you hear grinding or buzzing during the drain cycle, this is the likely cause.

The drain pump is the motor that actively pushes water out of the dishwasher. When it fails, water has nowhere to go and sits in the bottom of the tub. You might hear a humming sound (pump trying but failing) or complete silence during the drain phase. Drain pump replacement requires disassembly and is best handled by a technician.

5. The Air Gap or High Loop Is Missing

Dishwashers need either an air gap (a small device mounted on the countertop or sink) or a high loop (the drain hose looped up near the top of the cabinet) to prevent dirty sink water from flowing back into the dishwasher. Without one, water can siphon back and cause standing water that looks like a drainage failure. The correct high-loop or air-gap arrangement depends on the dishwasher instructions and local plumbing requirements. If the dishwasher was recently installed or the plumbing changed, compare the hose route with the model manual.

6. The Check Valve Is Stuck

The check valve (or flapper valve) is a one-way valve that prevents drained water from flowing back into the dishwasher. If it is stuck closed, water cannot drain out. If it is stuck open, water flows back in after draining, leaving a small amount of standing water at the end of the cycle. This part is usually located near the drain pump and requires partial disassembly to inspect. It is inexpensive but requires correct diagnosis.

7. A Control Board Issue Is Preventing the Drain Cycle

Modern dishwashers use electronic control boards to manage every phase of the wash cycle, including draining. If the board has a fault, it may skip the drain cycle entirely even though washing and rinsing work fine. Clues: the dishwasher completes the wash cycle but never initiates draining, error codes appear on the display, or the drain works when manually activated but not during normal cycles. Control board diagnosis requires testing with a multimeter and should be done by a qualified appliance repair technician.

Error Codes by Brand

Brand	Error Code	Meaning
Bosch	E24	Drain fault – usually kinked hose or pump blockage
Samsung	5C / SC	Drain failure – often food debris in the pump
LG	OE	Drain timeout – check filter and pump
Whirlpool / Maytag	F9 E1	Long drain – pump or hose issue
Miele	F11	Drain error – fine filter or drain pump

How to Prevent Dishwasher Drainage Problems

Scrape plates before loading – you do not need to pre-rinse, but large food scraps should go in the garbage
Clean the filter on the model schedule – and whenever visible debris collects
Run hot water at the sink before starting the dishwasher – this dissolves grease from the start of the cycle
Run a cleaning cycle monthly – use only the cleaning product and empty-cycle method approved in the model manual
Check the drain hose annually – look for kinks, cracks, or buildup where it connects under the sink

Dishwasher Still Not Draining? We Can Help Today.

Repair appointments are available across Halifax, Dartmouth, Bedford, and HRM. Same-day times are often available, depending on scheduling, travel, and parts availability. 3-Month Parts and Labour Warranty.

Book a Technician

or call (902) 904-5559

Frequently Asked Questions

Why is my dishwasher not draining but no error code is showing?

The most common causes that do not trigger an error code are a clogged drain filter, a kinked drain hose, or a garbage disposal blockage. These mechanical obstructions stop water from moving but do not always register as a fault on the control board. Start by removing and cleaning the filter at the bottom of the tub, then run the garbage disposal for 20 seconds, then check the drain hose under the sink for kinks. In most cases, one of these three steps will resolve the problem.

Can I run my dishwasher if it has standing water at the bottom?

It is not recommended. Running a dishwasher with standing water means the next cycle will mix with old dirty water, leaving dishes unclean and potentially spreading bacteria. It also puts strain on the drain pump, which is trying to push water through a blockage. Clean the filter first – if that does not resolve it, have a technician look at it before running more cycles.

How much does dishwasher drain repair cost in Halifax?

Simple repairs like a clogged filter, hose kink, or check valve replacement typically cost $80 to $150 including the service call. A drain pump replacement runs $150 to $280 parts and labour. A control board is more – $200 to $400 depending on the brand. At Max Appliance Repair we give you a firm quote before any work begins. Call (902) 904-5559 to book a diagnostic visit.

Is it worth repairing a dishwasher that is not draining, or should I replace it?

For most dishwashers under 10 years old, repair is the better financial choice. A drain pump or control board repair at $150 to $350 is far less than a new mid-range dishwasher at $700 to $1,200 installed. On a dishwasher over 12 years old with a major repair needed, replacement starts to make sense. Our technicians will give you an honest recommendation based on the repair cost and the age of your appliance.

What is the Bosch E24 error and how do I fix it?

The Bosch E24 error means the dishwasher has failed to drain within the expected time. Start by cleaning the fine mesh filter at the bottom of the tub – Bosch dishwashers have a two-part filter system that requires monthly cleaning. Then check the drain hose behind the dishwasher for kinks. If neither resolves it, the drain pump or check valve likely needs replacement. Bosch drain pump repairs are one of our most common dishwasher service calls in Halifax.

Samsung Fridge Not Cooling? Here Is What to Check

Troubleshooting guide covering demo mode, coils, and error codes

Appliance Repair Cost Guide – Halifax 2026

What to expect to pay for common repairs in Nova Scotia

Need a hand with this? Max Appliance Repair Halifax offers dishwasher repair appointments in Halifax. Same-day times are often available, depending on scheduling, travel, and parts availability. The service-call fee is waived when the recommended repair is completed. Call (902) 904-5559.

Appliance Tips, Repair Guides

Why Is My Dishwasher Not Draining? 7 Causes and How to Fix Them